Home > Products > RF Connectors > 1 mm W1 Connectors

Products

110 GHz 1 mm Jack PCB Connector Edge Launch

Description: 1 mm, Female, Straight, Edge Launch, PCB Conn (SUS), with .005" Pin (Solderless), Apply to Edge Launch, Work to 110 GHz
● VSWR: ≤ 1.50 @ 110 GHz
● Insertion Loss Value: ≤ 1.26 dB @ 110 GHz
● Durability Cycles: ≥ 500 Cycles
● Body Material: Stainless Steel 303
● Center Contact Material: Beryllium Copper
● 50 Ohms

Send Inquiry

Description

Introduction

This 1 mm connector uses a threaded interface, it possesses high precision structure with optimized impedance matching and stringent tolerance, that provide excellent electrical performance from DC to 110 GHz when connecting to PCB. Benefiting from Stainless steel design, it has outstanding durability in mechanically. The best advantage of this connector is "solderless" and "Reusable", which make connectors can be easily applied to PCB and save a lot time and cost. It works in W wave band, 80 GHz to 100 Ghz, wave length is 3 mm or so. It requires very stringent machining, plating, assembling process. For keep 110 Ghz performance, PCB's design & production must be good enough, rogers PCB is recommended.

Specification

Electrical
● Impedance: 50 Ω	● Insulation Resistance: 1000 MΩ Min
● Frequency Range: DC – 110 GHz	● Dielectric Withstanding Voltage: 500 Vrms Min (Sea Level)
● VSWR: 1.50 Max @ 110 GHz	● Contact Resistance: ≤ 4 mΩ (Center Contact)
● Insertion Loss: ≤ 1.26 dB @ 110 GHz	≤ 2 mΩ (Outer Contact)
Mechanical
● Mateable with W1 Series	● Center Contact Retention Force: 3 lbs Min
● Durability: ≥ 500 Cycles	● Coupling Torque: 3.6 - 4.4 lb-in Recommended
Environmental
● Temperature Range: -55 ℃ to +165 ℃
Material & Finish
● Body: Stainless Steel, Passivated	● Dielectric: Engineering Plastic, Natural
● Center Contact: Beryllium Copper, 30 μ" Gold

Features and Benefits

● Gold Plated Beryllium Copper Contact

● Stainless Steel Design

● High frequency

● No hurting to PCB

● Solderless

Applications

● Signal integrity analysis

● Research & Development Labs

● High Speed Data test

● Radio frequency System

Outline Drawing

FAQ

1. A measure of how much power is reflected

■ Return Loss: The portion of a signal that is lost due to a reflection of power at a line discontinuity. Return Loss is similar to VSWR and is generally preferred in the CATV industry to a VSWR specification

Return Loss = Ratio of reflected to incident power in dB

■ VSWR: Acronym for Voltage Standing Wave Ratio. VSWR is the ratio of voltage applied to voltage reflected. It is the major factor contributing to the total signal efficiency of the connector.

VSWR = Ratio of maximum to minimum electric field (Voltage)

Best performance is achieved when the impedance of the cable and the connector are the same (matched)

■ Insertion Loss

Insertion Loss is expressed in dB, and is a measure of the total loss of power going through a device

IL = -20*log (Pout/Pin)

Includes losses due to reflection (usually the dominant factor unless the Return Loss is very low <-26 dB), plus losses due to the dielectric and metal conductors (Attenuation)

■ Passive Intermodulation Distortion

Spurious Signals created by non-linear mixing of 2 or more frequencies in a passive device

F_IM3 = 2* F1-F2

dBm: measure of power relative to 1 milliwatt

dBc: measure of dB below a specified carrier level

2. The type of transmission line will determine the connector style

Cable Connector-Coaxial Cable, Twin Line

Surface Mount Connector-Microstrip

Edge Launch Connector-Microstrip, Stripline, Coplanar

End Launch Connector-Microstrip, Coplanar

Surface Launch Connector-Microstrip, Stripline, Coplanar

Packaging, Shipping