Latest Products
Contact Us
- The 3rd floor, Building A, Baolai Mansion, Hechang Road, Luozu Community, Shiyan Sub-district, Bao'an District, Shenzhen City
- sales@hualinkrf.com
- +86-755-88896526
1 mm Jack End Launch PCB Connector
Description: 1 mm, Female, Straight, End Launch (High), PCB Connector, with .005" Pin (Solderless), Apply to End Launch PCB , Work to 110 GHz
● VSWR: 1.50 Max @ 110 GHz
● Insertion Loss: ≤ 1.47 dB @ 110 GHz
● Mating/unmating Life: ≥ 500 Cycles
● 1 mm Body Material: Stainless Steel
● Housing Material: Brass
● Contact Pin Material: Becu
Description
Introduction
Hualink high-performance 1 mm female End Launch connectors are designed to provide less reflection up to 110 GHz for single-layer and multi-layer printed circuit boards where the high-frequency signal is on the top layer. It's designed into 2 pieces for more stable installation on PCB, solderless design for both grounding and signal make it high-efficiency to install or uninstall, which save a lot of time and cost. Comparing to Standard High Profile version, low profile is more suitable if application limit the space.
Specification
Electrical | |
● Impedance: 50 Ω | ● Insulation Resistance: 1000 MΩ Min |
● Frequency Range: DC – 110 GHz | ● Dielectric Withstanding Voltage: 500 Vrms Min (Sea Level) |
● VSWR: 1.50 Max @ 110 GHz | ● Contact Resistance: ≤ 3 mΩ (Center Contact) |
● Insertion Loss: ≤ 1.47 dB @ 110 GHz | ≤ 2 mΩ (Outer Contact) |
Mechanical | |
● Mateable with W1 Series | ● Center Contact Retention Force: 3 lbs Min |
● Durability: ≥ 500 Cycles | ● Coupling Torque: 3.6-4.4 lb-in Recommended |
Environmental | |
● Temperature Range: -55 ℃ to +165 ℃ | |
Material & Finish | |
● Body: Brass and SUS303 | ● Dielectric: Engineering Plastic, Natural |
● Center Contact: Beryllium Copper, 30 μ" Gold | |
Features and Benefits
● Good Return Loss
● Low Insertion Loss
● Low RF Leakage
● High Precision
● Excellent Repeatability
Applications
● Optical Module Test
● Signal Test
● RF Engineering
● Communications
● Aerospace
Outline Drawing
Related Products
Hualink PN | DESCRIPTION | Picture |
10-S-P-SPN-ST-EL0090-01U | 1 mm Female Straight End Launch (Solderless) |
|
10-S-P-SPN-ST-EL0090-01LU | 1 mm Female Straight End Launch (Low profile) |
|
FAQ
1. End Launch Connectors – Installation Procedure
Step 1: Mount the end launch connector on the board in the desired position through 2 holes.
Step 2: Ensure the launch pin is centered on the signal trace of PCB.
Step 3: Ensure the housing is tight against the side face of PCB.
Step 4: Tighten the 1-72 mounting screws until the connector is not moving.
Step 5: Keep PCB and Connectors clear
2. DEFINITIONS
■ Coplanar ground plane spacing = trace width + gap + gap. This is the distance from the inside edge of one top ground plane to the inside edge of the other top ground plane.
■ Microstrip-to-coplanar transition = When using microstrip on a multilayer board or on a board where the microwave ground is not accessible, then a microstrip-to-coplanar transition should be used.
■ Transition Block = The portion of the End Launch connector assembly where the high frequency signal transition from the coax connector onto the printed circuit board.
■ Ground stitching = These are vias connecting the top ground planes with the substrate ground. The purpose of the vias is to ensure both coplanar ground planes stay at the same potential. The best placement of these is near the trace at a distance of ¼ wavelength of the highest frequency.
3. Hualink 1 mm connector
The working frequency of 1 mm series can reach up to 110 GHz. They adopt reliable threaded connection methods and are applied in fields of communication, precision testing, automobiles, satellites, radar, radio astronomy and other ultra-high requirements millimeter wave fields. The dielectric adopts the air, and the thread adopts metric M4×0.7P. The design size is smaller than 1.85 mm, and it is currently the smallest millimeter wave connector in the world.
Packaging, Shipping
Hot Tags: 1 mm jack end launch pcb connector, China, suppliers, customized, OEM, ODM, SMA Male To SMA Male Cable Assemblies, 2.4 mm RF Cable Assembly, 1 mm Jack End Launch PCB Connector, SMA Mixed Tech PCB Connector, Vertical Launch SMA, K Jack Through Hole RF Connector
You Might Also Like
